Answer
We recommend installing axles with a 1.5° bend for the front of the car and 2.5° bend for the rear. The axles heads are marked in the direction of the bend. Install the axles with the mark straight up. The alignment procedure requires turning the axles while they are in the car slot.
Regarding this, are Bent Axles legal in Pinewood Derby?
Axles are LEGAL in all races. LATHED shaft and underside of axle head to remove Crimp marks and Burrs – these must be removed to make your car fast. POLISHED axle shaft to minimise friction, increasing your car speed.
Subsequently, question is, can you glue axles on Pinewood Derby car?
For pinewood derby cars, white glue works fine for glueing wood to wood (such as adding wood accessories) and for repairing chips or cracks in the wood. It can also be used for holding the axles in place. White glue doesn’t work well on metal, so don’t use it to glue metal accessories or weight to the car.
In this way, what angle do you bend a Pinewood Derby axle?
It is best to bend the axles slightly (1 to 2 degree) then insert in the block. The bend should be at the point that the axle exits the block.
How much does it cost to bend a Pinewood Derby axle?
We recommend installing axles with a 1.5° bend for the front of the car and 2.5° bend for the rear. The axles heads are marked in the direction of the bend. Install the axles with the mark straight up.
28 Related Question Answers Found
How do you balance Pinewood Derby wheels?
All tyres are out of balance even though they were turned on a lathe. You then balance out the wheel by removing the excess weight from the heavy side or by adding weight to the light side [by adding nail polish or something] until a balanced wheel is achieved.
Where do you put the wheels on a Pinewood Derby car?
Pinewood Derby Axle Installer Lubricate the wheel and axle – Slide the axle into the wheel. Place the wheel/axle on the base with the pointed end of the axle up. Place the Axle Guide in the axle slot. Hold the Axle Guide in place with your thumb then gently press the car body straight down on the axle.
How do you make a Pinewood Derby car rider?
Steer the Car Insert one of our 1.5 Degree Steering Axles into the right front wheel and into the block. Align the screwdriver slot in the axle head vertically, so the steering slot is straight up and down. Next, you need to measure the car’s drift to steer it for rail riding.
Should I bake my Pinewood Derby block?
Bake the Block: Start with your block of wood, and before you do anything else, bake it in the oven at 250 degrees for around two hours to remove moisture and make it lighter. This will allow you to place more weight to the rear of the Pinewood Derby car where you actually want it.
Can you put weights on the bottom of a Pinewood Derby car?
The weight should not extend past the rear of the car. Glue bottom weights to the bottom of the block to bring the total weight (including wheels and axles) to 5 oz. Install some of the weight behind the rear axle and the rest in front of the axle. The weight can be broken apart with pliers.
Should you sand Pinewood Derby wheels?
Lightly Sanded BSA Wheels This wheel should be legal in pinewood derby races that specify any of the following: Wheel diameter must be greater than 1.18″. The wheels may be slightly sanded to remove any mould marks but may not be modified in any other way.
Where is the best place to put the weight on a Pinewood Derby car?
PUT MOST OF THE WEIGHT IN THE BACK Science says the heaviest part of your car should be about 1 inch in front of the rear axle.
Where do you bend Pinewood Derby axles?
One way is to first bend the axle with the Pro Axle Press and Pro Rail Rider Tool. Then, before you remove the axle, place a black dot on the head at the most downward position (6:00). (6:00). When the axles are later installed the black dot will be placed straight up at the 12:00 position.
How do you polish Pinewood Derby axles?
Use wet/dry sandpaper starting with CAMI 400 grit (30 micron = 30 μm = 0.03 mm). Cut the sandpaper into 1/4″ strips that are several inches long. Dip the paper in water and sand the exposed portion of the axle for approximately 30 seconds with the axle rotating at high speed. Don’t forget to polish under the axle head.
ncG1vNJzZmivp6x7r6%2FEq6upp5mjwW%2BvzqZma2hiZ3xxfY6hprBllKR6urvUZqysnV2WeqOxza1kmrCcmnqwuoyaZKmhnprEsLvDZpueqpKueqSt0WefraWc